G1 Original Pipe Chanter Reed (IN STOCK)
Quantity in Basket:
NonePrice:
$16.00Shipping Weight:
0.02 poundsG1 reeds are made solely by John Elliott of Scotland, using a combination of traditional and innovative techniques producing a precision reed. Each tube of cane is personally hand selected and only the best are deemed acceptable for G1’s high standards. The cane is sourced from top cane growers in France and Spain depending on the season. It is then treated and prepared in a highly skilled process. All reeds are pre-tested and individually tested.
Selecting a Pipe Chanter
Reed
You never see a professional player struggling to play the bagpipe; they always
seem relaxed and comfortable. The pipe bag is the correct size, is 100%
airtight, stocks are tied in correctly and have no cracks, the blowpipe
is the correct fit, the valve is functioning properly and all the joints
are hemped correctly (see the past 3 articles). If you have corrected
these problems and the pipe is still difficult to play the next thing to address
is the pipe chanter reed . Many pipers get into the bad habit of trying
to blow reeds that are much too strong for them. Nothing can hamper your
technique and expression more than trying to play a bagpipe reed that is too
hard for you. Pipe bands are one of the biggest contributors to this problem by
insisting that reeds must be stiff and difficult to blow in order to contribute
to the sound of the band, don't get suckered into this myth. It is not the goal
of this article to teach pipe chanter reed adjustment, (that will come later)
but rather to help in your selection of a reed that is within your playing
comfort level. The question I am asked the most is "What strength reed should I
play easy, medium, strong or something in between"? The answer is none of the
above, you have to play a reed that is within your own personal comfort level.
What may be a strong reed for one person might be a medium reed for another
person.
How do I choose a G1 pipe chanter
reed
Visual Test:
1. The reed should have a nice
clean look with no splits down the length of the cane and no chipped corners.
2. Both reed blades should be the same thickness and must fit tight together
with no gaps.
3. The blades at the open end should have a nice elliptical
shape.
Airtight Test:
Hold the reed in one hand and place a
finger over the cane tip's end of the reed to seal it and blow through the reed
from the staple end, run a finger of your other hand down both sides of the reed
to ensure that no air is leaking from the blades. If the reed is leaking air
discard it.
Chanter Test:
Now place the reed of your choice
into the reed seat of the pipe chanter and take a deep breath. Form a tight seal
with your lips around the lacquered hemp on the pipe chanter reed (not over the
hemped end of the pipe chanter) and play the scale from Low A to High A and then
back down to Low A. If you can't do this in one breath - the reed is too strong
for you to play comfortably, select another reed. When you find a reed that will
pass this test, that is the correct strength reed for you in your present
playing condition. By following these three steps you should be able to select a
reed that will give you many hours of comfortable playing.
Learn by doing!
Pipe Chanter Reeds.
To change the strength and pitch of a pipe chanter reed, if the reed is only slightly too strong:
1. Pipe chanter reed with reed elastic. Wrap the elastic 2 to 3 times around the reed.
2. The higher the elastic, the easier the reed is to play.
3. The lower the elastic, the stronger the reed is to play.
Once you have the reed at a comfortable strength you may have to raise or lower the reed in the reed seat by adding or subtracting hemp in order to achieve the correct pitch.
To change a much stronger reed:
4. Divide the reed into thirds, the top line approximately 1/8" down from the top of the reed and the bottom line approximately 1/4" up from the hemp binding.
5. Fold a piece of 220 grit sand paper over the corner of a table. You are now going to remove material from the middle third of the reed.
6. Hold the reed so that you are sanding the shoulder of one side of the reed then across the flat surface to the other shoulder, repeat this 4 to 5 times, flip the reed and do the same on the other side, then test the reed, if it is still too strong keep repeating till you achieve the strength you are looking for.